Elitech IPT-100, IPT-100S Temperature and Humidity Data Logger

安全说明

• To ensure proper installation and usage of this product, please read carefully and follow the guidelines below:

电池

1. Use three AAA batteries. Do not use other types of batteries to avoid damaging the device or causing other malfunctions.
2. Do not disassemble, crush, strike, or heat the batteries. Do not place them in fire, as this may cause the batteries to explode and trigger a fire.

设备

1. Do not use the device in flammable or explosive gas environments to avoid the risk of explosion or fire.
2. lf the device emits a burnt smell or other unusual odors, disconnect the power and contact the manufacturer or supplier immediately.

防范措施

• If the device will not be used for an extended period, remove the batteries and store the device in a dry, cool environment.
• Users are not allowed to make any unauthorized changes to the device.
• Unauthorized modifications may affect the accuracy of the device or even cause damage.
• Do not use the device outdoors to avoid malfunctions caused by rain, lightning, or other adverse weather conditions.
• Use the device within its designated temperature and humidity range.
• Do not subject the product to heavy impact.
• Measurement values may be affected by the following factors:
• 温度误差：
  • Insufficient stabilization time in the measurement environment.
    Proximity to heat or cold sources or direct exposure to sunlight.
• 湿度误差：
  • Insufficient stabilization time in the measurement environment.Long-term exposure to steam, mist, water curtains, or condensation environments.
• 污染：
  Presence of dust or other pollutants in the environment.

产品结束view

• The temperature and humidity meter is designed for industrial workshops, warehousespharmacies, laboratories, agricultural environments, and other professional settings for monitoring environmental temperature and humidity.

产品特性

• Supports OTA updates for continuous improvements.
• 数据可以 viewed and traced through the mobile app for easier tracking.
• Scenario-based configuration with smart alerts.
• 4-inch large screen for clear data display.

产品外观

1.  最大/最小按钮
2. ℃/℉ toggle button
3. Mode/Bluetooth button
4. External probe interface
5. 磁铁
6. 电池盖
7. 站立
8. External temperature sensor (Standard for IPT-100S)

产品界面

1. 电池电量图标
2. 蓝牙图标
3. Placeholder icon (no function)
4. 警报图标
5. Recording display icon
6. External probe display mode
7. Max/Min indicator icon
8. 时间显示区
9. Backtrack temperature display area
10. Backtrack time indicator area
11. 温度显示区
12. Over-limit status display (over upper limit , over lower limit
13. Humidity range indicator area
14. 湿度显示区

技术参数

测量范围	温度：-10°C~50°C
	Humidity:10%RH~99%RH
准确性	Temperature:+0.5°C(10-35°C),+1°C for other ranges
	Humidity: +5%RH(40%-75%),+10% for other ranges
解决	温度：0.1°C
	湿度：0.1％RH
电源	3*AAA
待机时间	Not less than 6 months
屏幕	4.5-inch segmented display
数据记录	Not less than 5000 entries
蓝牙范围	Up to 30 meters in an open environment
操作环境	-20~60℃，0~90%RH（无冷凝）
存储环境	-25~65℃，0~90%RH（无冷凝）
方面	118.6*99.5*23.0毫米

Accessories External Probe

• (Applicable only to IPT-100S with built-in external probe)
  

  测量范围	Temperature:-20°C~70℃
  准确性	Temperature:+0.5°C(0℃~40°℃),+1°C for other ranges
  解决	温度：0.1℃
  接口类型	Type-C port (Note: This port does not support charging!)
  操作环境	-40~85℃，0~90%RH（无冷凝）
  存储环境	-50~90℃，0~90%RH（无冷凝）
  传感器类型	数字温度传感器
  行长度	2 米

产品特性

1. 产品激活
   • Remove the insulating strip from the back of the product to power it on. The screen will display all data for 2 seconds and then show the real-time readings from the internal sensor.
   • Note: After powering on, connect the device to your phone via Bluetooth to sync the time. If not in use for a long period, remove the batteries and store them separately.
   • The Type-C interface is only for connecting the external probe, not for charging.
2. .Button Functions:
   

   按钮	短按	长按2s
   	Switch between max, min, and current values	Clear maximum and minimum values
   	Toggle backtrack time	Switch temperature unit (°C/°F)
   Switch between internal/external probe data display		启用/禁用蓝牙

3. 模式切换：
   Press the mode button to switch between the internal sensor’s temperature and humidity data and the external probe’s temperature data.
   • Note: If no external probe is connected, the external probe mode will show “—” and the external probe icon will light up.
4. View Max/Min Values:
   • short Press the max/min button to cycle between the maximum, minimum, and current values in the current mode.
   • Long-press the button to reset the maximum and minimum values.
5. Humidity Indicator:
   • By default, when the humidity is below 40%, the indicator turns red to show dry conditions. Between 40%-60%, it turns green to show comfortable conditions, and above 60%, it turns blue to show humid conditions. The app allows customization of these ranges.
   • Note: Default values are based on the “Indoor Air Quality Standard” (GB/T 18883-2022)
6. Product Alarms
   

   展示	原因	解决方案
   嘟	Current data exceeds the limit	Automatic mute after 60 seconds, or press any key to mute
   	Current data exceeds 限制	Automatically cancels when data 恢复正常
   	Exceeded the upper limit of the display range	Automatically cancels when data returns to normal
   	Exceeded the lower limit of the display range 未检测到传感器	Automatically cancels when data returns to normal   Insert or replace the sensor

APP操作说明

APP连接

1. Scan the QR code below to download and install the dedicated APP, or search for “Elitech Tools” in the app store to install.
2. 长按 Bluetooth button for 2 seconds to enable Bluetooth. The Bluetooth icon will flash. Open the “Elitech Tools” app, search for nearby devices, find the correct model, and click to connect.

• • Note: Ensure your phone’s Bluetooth is enabled while using the app. The device’s Bluetooth will automatically turn off if not connected within 2 minutes.

APP界面介绍

• The main interface displays the current built-in temperature, humidity, probe temperature, and max/min value. By clicking , you can reset the max/min values. When the temperature or humidity exceeds the upper or lower alarm limits, the alarm icon will appear in the corresponding alarm  zone
• Click the text in the upper right corner to switch Scene Mode
• Click the dial to switch to the curve interface and view the temperature and humidity curves.
• Click “Settings” to modify relevant parameters
• Click “Scene Settings” to select the scene you want to modify
• Modify the alarm parameters for this scene.
• Modify humidity range value

附件清单

• Recording-type Temperature and Humidity Meter *1
• AAA Batteries *3
• 磁铁*2
• External Temperature Sensor Probe *1
• (only for IPT-100S with built-in external probe)

常问问题

问：设备可以在室外使用吗？

A: No, the device should not be used outdoors to avoid malfunctions caused by adverse weather conditions.

问：如何校准设备？

A: Calibration is not user-accessible. Please contact customer Support if you believe your device requires calibration.

文件/资源

Elitech IPT-100, IPT-100S Temperature and Humidity Data Logger [pdf] 使用说明书 IPT-100, IPT-100S, IPT-100 IPT-100S Temperature and Humidity Data Logger, IPT-100 IPT-100S, Temperature and Humidity Data Logger, Humidity Data Logger, Data Logger, Logger

参考

• 用户手册